Changsha Sollroc Engineering Equipments Co., Ltd
FOCUS IN MANUFACTURING OF HIGH QUALITY DTH AND RC DRILLING TOOLS.
Add to Cart
SRC040 Weight 17 kgs Black 5 3/4'' 146mm RC Drill Bit For Water Well Drilling
Product Introduce:
Reverse Circulation drilling, or RC drilling, is a method of drilling which uses dual wall drill rods that consist of an outer drill rod with an inner tube. These hollow inner tubes allow the drill cuttings to be transported back to the surface in a continuous, steady flow.
Specification:
SOLLROC RC BIT130MM WITH OTHER SHANK
| Diameter | Shank | Buttons * button diameter | Shroud diameter (mm) | weight (kg) | ||
| mm | inch | Gauge | Centre | |||
| 146 | 5 3/4 | SRC040 | 8*16mm | 6*16mm + 3*14mm | 144 | 17 |
SOLLROC RC BIT model SRC040:
| Diameter | Buttons * button diameter | Shroud diameter (mm) | weight (kg) | ||
| mm | inch | Gauge | Centre | ||
| 121 | 4 3/4 | 8*14mm | 8*14mm | 119 | 10.7 |
| 124 | 4 7/8 | 8*14mm | 9*14mm | 122 | 14.5 |
| 127 | 5 | 8*14mm | 9*14mm | 125 | 14.7 |
| 130 | 5 1/8 | 8*14mm | 9*14mm | 128 | 14.9 |
| 133 | 5 1/4 | 8*16mm | 9*14mm | 131 | 15 |
| 135 | 5 3/8 | 8*16mm | 6*16mm + 3*14mm | 133 | 15.4 |
| 137 | 5 3/4 | 8*16mm | 6*16mm + 3*14mm | 135 | 15.8 |
| 140 | 5 1/2 | 8*16mm | 6*16mm + 3*14mm | 138 | 16 |
| 143 | 5 5/8 | 8*16mm | 6*16mm + 3*14mm | 141 | 16.5 |
| 146 | 5 3/4 | 8*16mm | 6*16mm + 3*14mm | 144 | 17 |
Adavantages:
1.Samples extracted are reliable and free of contaminants;
2.The method is timely and cost-efficient;
3.Well-suited for difficult terrains;
4.High penetration rates, and it has minimal environmental impact.
5.Drills faster through soft formations with less blockages
Basics of Reverse Circulation Drilling:
(1) RC drilling uses rods with inner and outer tubes, the drill cuttings are returned to surface inside the rods. The drilling mechanism is a pneumatic reciprocating piston known as a hammer driving a tungsten-steel drill bit.
(2) RC drilling utilizes much larger rigs and machinery and depths of up to 500 meters are routinely achieved. RC drilling ideally produces dry rock chips, as large air compressors dry the rock out ahead of the advancing drill bit.
(3) RC drilling is slower and costlier but achieves better penetration than RAB or air core drilling; it is cheaper than diamond coring and is thus preferred for most mineral exploration work.
(4) Reverse circulation is achieved by blowing air down the annulus of the rod, the differential pressure creating air lift of the water and cuttings up the inner tube which is inside each rod. It reaches the deflector box at the top of the drill string then moves through a sample hose which is attached to the top of the cyclone.
The drill cuttings travel around the inside of the cyclone until they fall through an opening at the bottom and are collected in a sample bag. For any drill hole there will be a large number of sample bags, each one marked to record the location and drilling depth that the sample was obtained.
The collected series of sample bag cuttings are later taken for analysis to determine the mineral composition of the drill hole. The analysis results of each individual bag represents the mineral composition at a particular sample point in the drill hole. Geologists can then survey the drilled ground analysis and make decisions about the value of the overall mineral deposit.
Photo:
About us:
SOLLROC Reverse Circulation drilling (RC) ,from size 3’’ to 5.5’’, is a technique of drilling that uses dual wall drill rods that consist of an outer drill rod with an inner tube. By using compressed air to extract rock fragments sample,the samples travel through rods to a sample splitter at surface, avoiding all contact between the samples and the borehole wall that allows samples to be retrieved with minimal contamination,which is mainly used in deep hole exploration and mining grade control.
Delivery Way:
By Air, By express or By Sea
Package :
Ply-wooden cases + pallet